Why is my spa overheating?

If the spa is located in an area that is experiencing hot weather, it is normal to have the spa water temperature rise. To help keep your spa cooler, adjust the spa’s filtration cycles to no more than three hours per day, and only one hour per day during the warmer summer months. Set the cycles to run during later evening or early morning hours when the outside air temperature is cooler. During the summer, set only one filter cycle per day. Open the cover for several minutes, long enough to allow the water to cool down. Repeat a couple times weekly as necessary. For safety reasons, never leave your spa unattended with the cover open. If OHH is displayed on the control panel, this means that the thermometer has detected spa water temperature above 110 degrees F. Do not use the spa at this temperature. Take the advised steps above to cool your spa water to below 106 degrees F before use.

Why won't my spa heat?

If your spa temperature is low, first check the thermostat to see if it has been turned down or set to low heat range. Adjust the thermostat to desired temperature or set to high heat range. Another common reason for your spa temperature to be low is because the high limit sensor has tripped. Press any button on your control panel to reset the system. If neither of the above steps works, your heating system may be defective. Contact your authorized Bullfrog Spas Dealer for further diagnosis.

Why is my GFCI breaker tripping?

Warning: You must be a qualitied electrician and or service technician to perform diagnosing or serial injury or death can result: High voltage components are in use. If the spa was recently installed, the most common reason the GFCI would trip is the Load Neutral (white wire) between the spa and GFCI which must be connected to the Load Neutral port in the GFCI breaker. If the neutral wire is connected to the neutral busbar, the breaker will trip during startup. The neutral connection must not have contact to the ground on the load side of the breaker or it will trip. If the spa is not tripping immediately upon startup, a process of elimination should be used to identify the problem. Disconnect one component at a time from the control board and try restarting the spa. If the breaker trips, reconnect the component then try again by disconnecting a different component. Continue repeating this process until the breaker does not trip. Components include pumps, heaters, lights, stereos, ozone, etc. If the breaker does not trip after disconnecting the component, then the disconnected component is the source of the problem. Once you have determined which component is at fault, replace the component. If you have not found the source of the problem after disconnecting each spa component individually, disconnect all components from the control board and try starting the spa. If the breaker still trips, a certified electrician will need to inspect the breaker and wiring.

Why is my spa making a vibration noise?

A light vibration noise is normal while the spa pumps and motors are running. If your spa’s vibration noise level seems excessive, the first thing to check for is the spa motor’s shipping bolts. Each spa motor has a shipping bolt that can contribute to the vibrating noise and can be removed once your spa is delivered and installed. The bolts have tags with red lettering for easy identification. If the bolts have been removed and your spa still makes an excessive vibration noise, contact your spa dealer for further assistance.

Why is my spa pump creating a burning smell or making excessive noise?

If your spa pump is creating a burning smell or making excessive noise, the pump motor is defective. This can happen when running the pump during high ambient outside temperatures or due to excessive run times. Please contact your authorized Bullfrog Spas dealer for replacing the pump.

Why are my control pad and spa equipment not operating?

If your hot tub control pad and spa equipment are not operating, that means you have no electrical power to the spa. Turn on or reset the GFCI circuit breaker to supply the spa with power again. If this does not solve the problem, have a qualified Electrician check the electrical service for issues. Another reason your control pad and equipment won’t work is if the fuse (20 or 30A depending on the system) has blown. Contact your authorized Bullfrog Spas Dealer for repair/replacement.

Why are my hot tub jets not working?

If your hot tub jets are surging on and off, the first thing to check is your water level as it might be too low. Adjust water to the water level indication mark on the faceplate of the filter assembly. Next, check your filters as they may be dirty. If so, clean or replace them. If your spa’s jets seem weak or are not working, first double-check to make sure that the valves are open. JetPaks have valves at the bottom that open and close by turning the valve. Adjustable jets on M Series, A Series, R Series, and STIL spas open and close by turning the jet face. Adjustable jets on X Series spas open and close by turning the outer ring. The next thing to check is the suction fitting(s) normally located at the bottom of your spa shell to see if they are blocked. Remove any debris you find by hand or with a spa vacuum. If your jets are not working after filling your spa, you most likely have an airlock in the pump. Follow the directions in the “how do I fix an airlock in the pump” section below.

Why won’t my spa won't work after draining and refilling it?

If your spa pumps/jets are not working after filling your spa, you most likely have an airlock in the pumps. Follow the directions in the “how do I fix an airlock in the pump” section below.

How do I fix an airlock in the pump?

To prevent airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air as possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose directly in the filter. Detailed instructions for filling each spa series are found in your owner’s manual. Your hot tub’s pumps must be primed directly after filling to ensure correct operation of your spa and get rid of any airlocks. After initial startup, verify that the home status screen appears on the panel. Depending on your spa model, your spa has either 1,2, or 3 pumps. To prime the pumps, press the “Jets 1” button once to prime in low-speed. After the pump turns on and water is visibly flowing from the jets wait a few seconds and then press “Jets 1” again to initiate highspeed operation of Pump 1. The pump has primed when water is flowing from the jets. If your spa is equipped with a second jet pump, repeat the priming process for Pump 2 by pressing the “Jets 2” button once to turn on low speed and then a second time to turn Pump 2 on high. If your spa has a 3rd pump, press the “Jets 3” button to prime the third jet pump. All pumps will have primed when water is observed flowing from the jets associated with each pump. On rare occasions, priming the pumps will not get rid of an airlock. The next step is to remove the front panel and locate the pump with an airlock. The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the union on the pump to let the air out until you see water. Do not attempt this while the spa pump is running. If you need help doing this or this does not resolve the problem, please contact your authorized Bullfrog Spa Dealer.

Why do my spa jets turn off during operation?

If your jets turn off automatically after either 30 or 60 minutes, this is completely normal. The automatic timer has completed its cycle. Simply turn the pump back on to start a new cycle. Another reason your jets can turn off unexpectedly is if the pump has overheated due to the vents on the equipment door being blocked. Clear away any items from the vents and wait a while to see if your jets work again. The last reason your spa jets can turn off is if the pump motor is defective. In this case, contact your authorized Bullfrog Spas dealer for service.

Why are my hot tub jets/pump not turning off?

If you are trying to turn off the pump for jets 1 on your spa and it appears that they are not turning off, your spa is in the middle of a filtration cycle. Spas not equipped with a dedicated filtration pump will turn on automatically, using jet pump 1 on low speed, to filter and/or heat. This is normal spa operation.

What do I do if my spa is leaking?

If you notice your spa is losing water, check all fittings and equipment in the equipment compartment for the source of leakage. If a leak is detected, tighten the fitting by hand. If the leak persists, you cannot find the source of the leak, or the leak is coming from the shell, contact your authorized Bullfrog Spas Dealer.

Best Hydrotherapy Hot Tubs

11 March

Share on
Share
Tweet
Share

Best Hydrotherapy Hot Tubs

Bullfrog Spas | Buying & Research Guide, Benefits & Features | No comment

In today’s fast-paced world, finding moments of relaxation and rejuvenation is crucial for maintaining our well-being. Many people choose to get a hot tub due to the health and hydrotherapy benefits. However, you may ask yourself, what is the best hydrotherapy hot tub? In this blog, we will be exploring hydrotherapy and the best hydrotherapy hot tub options available.

Understanding Hydrotherapy

To pick the best hydrotherapy hot tub, you must first understand what hydrotherapy is. Hydrotherapy derived from the Greek words “hydro” meaning water and “therapeia” meaning healing. It is a therapeutic approach that utilizes water to promote health and well-being. The best hot tubs designed for hydrotherapy typically feature jets that emit pulsating streams of water, targeting specific areas of the body to provide relief from aches, pains, and stress.

Factors to Consider

When choosing the best hydrotherapy hot tub, there are a few factors to pay attention to:

Jet Configurations

Jet configurations dictate the type and intensity of massage therapy the hot tub can provide, directly influencing the effectiveness of hydrotherapy sessions. By choosing a hot tub with versatile jet configurations, individuals can tailor their hydrotherapy experience to target specific muscle groups or areas of tension, promoting relaxation and alleviating discomfort. Additionally, the ability to customize jet positions and adjust their intensity ensures a personalized and therapeutic massage experience for each user. Ultimately, selecting a hot tub with the right jet configurations enhances the overall effectiveness and enjoyment of hydrotherapy, contributing to improved well-being and relaxation. Look for hot tubs with adjustable jets that allow you to customize your massage experience.

Bullfrog Spas is unique and widely known due to the patented JetPak Therapy System. Unlike conventional spas, JetPak technology allows users to personalize their relaxation sessions by easily swapping out different massage jets within a variety of massage seats. Each JetPak is uniquely engineered to target specific muscle groups, providing tailored therapy that caters to individual needs and preferences. This enhances versatility and ensures optimal performance and efficiency. With the JetPak Therapy System, Bullfrog Spas offers a spa experience that can be customized to suit any user’s desires, making relaxation and wellness truly personalized.

Seating Capacity

Consider how many people will be using the hot tub simultaneously. Whether you prefer an intimate soak for two or a larger tub for entertaining guests, choose a model that accommodates your needs. The number of seats directly influences the hot tub’s usability, accommodating both individual relaxation and social gatherings. A hot tub with adequate seating capacity ensures that users can comfortably enjoy the benefits of hydrotherapy. Moreover, a variety of seating options allows users to find their preferred position for optimal comfort and support during hydrotherapy sessions.

Filtration System

Paying close attention to the filtration system is essential when selecting the best hydrotherapy hot tub. A filtration system plays a critical role in maintaining water cleanliness and hygiene, which is vital for ensuring a safe hydrotherapy experience. Effective filtration removes contaminants, debris, and impurities from the water. A high-quality filtration system helps to prolong the lifespan of a hot tub, ultimately minimizing maintenance requirements and ensuring long-term durability. By prioritizing a hot tub with an efficient filtration system, individuals can rest assured that their hydrotherapy sessions will be both hygienic and rejuvenating, promoting overall health and well-being.

Energy Efficiency

When choosing the best hydrotherapy hot tub, consider a hot tub that is energy efficient. An energy-efficient hot tub not only reduces operating costs but also minimizes environmental impact. By selecting a model with advanced insulation, efficient pumps, and energy-saving features, users can significantly lower their electricity bills while enjoying their hot tub sessions. Energy-efficient hot tubs contribute to sustainability efforts by conserving resources and reducing carbon emissions. Investing in a hot tub with high energy efficiency is a wise and responsible choice for both personal and global well-being.

Durability

Pay attention to durability and warranty when selecting the best hydrotherapy hot tub. A durable hot tub ensures longevity and reliability without frequent repairs or replacements. By choosing a hot tub constructed from high-quality materials and construction, individuals can rest assured that their investment will withstand regular use.

Bullfrog Spas EnduraFrame and EnduraBase are constructed from sturdy materials ensuring that the spa maintains its structural integrity even in harsh outdoor environments. The EnduraFrame design also enhances ease of maintenance, with accessible components that simplify repairs and servicing. With its robust construction and thoughtful engineering, the Bullfrog Spas EnduraFrame ensures that owners can enjoy their spa for years to come, backed by a commitment to quality and reliability.

Warranty

A comprehensive warranty offers peace of mind, protecting against unexpected malfunctions and defects that may arise. A reputable manufacturer that stands behind their product with a strong warranty demonstrates confidence, further assuring customers of their investment’s value. Bullfrog Spas offers warranty to all their customers for their peace of mind and confidence in their investment.

Bullfrog Spas and Hydrotherapy

Hydrotherapy hot tubs offer numerous health benefits for the body and mind. By considering factors such as jet configuration, seating capacity, and energy efficiency, you can select the best hot tub to suit your needs. With its focus on customization, durability, and quality craftsmanship, Bullfrog Spas has established itself as a great option for the hydrotherapy hot tub market. However, no matter what you choose, make sure you’re investing in a high-quality hydrotherapy hot tub.

AUTHOR - Bullfrog Spas

Bullfrog Spas is a premier brand of personalized premium hot tubs. With proprietary hydromassage technology and an eye for contemporary design, Bullfrog Spas is revolutionizing the concept of the portable hot tub and providing a relaxation experience unlike any other. Discover the award winning spa of the future today.

Blog

Best Hydrotherapy Hot Tubs

Understanding Hydrotherapy

Factors to Consider

Jet Configurations

Seating Capacity

Filtration System

Energy Efficiency

Durability

Warranty

Bullfrog Spas and Hydrotherapy

AUTHOR - Bullfrog Spas

CUSTOMERS

OWNERS

DEALERS

COMPANY